Wheels

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Best seller. You'll be hard-pressed to find a better wheel anywhere near these prices.

- Elite Series convertible road disc hubs - Available in multiple axle configurations - Shimano and Campagnolo cassette body options with 6 pawl/48 point/7.5° engagement - Straight pull and J-bend spoke options - 6 bolt and Center Lock disc brake rotor options - Sealed bearings - Material: AL6061 Straight Pull Spoke/QR Axle: PCD-L: 35mm PCD-R: 49mm LTF-L: 32.75mm LTF-R: 50.05mm CTF-L: 34.9mm CTF-R: 17.6mm Straight Pull Spoke/12mm Thru-Axle: PCD-L: 35mm PCD-R: 49mm LTF-L: 36.25mm LTF-R: 53.55mm CTF-L: 34.9mm CTF-R: 17.6mm J-Bend Spoke/QR Axle: PCD-L: 45mm PCD-R: 50.6mm LTF-L: 32.65mm LTF-R: 48.2mm CTF-L: 35mm CTF-R: 19.45mm J-Bend Spoke/12mm Thru-Axle: PCD-L: 45mm PCD-R: 50.6mm LTF-L: 36.15mm LTF-R: 51.7mm CTF-L: 35mm CTF-R: 19.45mm

- Elite Series convertible road disc hubs - Available in multiple axle configurations - Straight pull and J-bend spoke options - 6 bolt and Center Lock disc brake rotor options - Sealed bearings - Material: AL6061 Straight Pull Spoke/6-Bolt Disc: PCD-L: 36mm PCD-R: 36mm LTF-L: 27.75mm LTF-R: 15.25mm CTF-L: 22.25mm CTF-R: 34.75mm J-Bend Spoke/Centerlock Disc: PCD-L: 45mm PCD-R: 45mm LTF-L: 27.25mm LTF-R: 15.45mm CTF-L: 22.75mm CTF-R: 34.55mm

- Unidirectional Toray T700 carbon fiber construction - Available in multiple widths for Cross Country, All Mountain, and Downhill applicarions - Reinforced nipple bed with directional drilling - Hookless bead design - Tubeless ready - Disc brake only - ISO-Mountain certified - ISO: 622 - Wall: Dbl - Side: Disc - Valve: PV - Tire Compatibility: Tubeless Compatible All Mountain: - Width ID: 27 - Width OD: 32 - Profile: 29 - Weight: 440g - ERD: 578 Downhill: - Width ID: 32 - Width OD: 38 - Profile: 31 - Weight: 500 - ERD: 584 Cross Country: - Width ID: 24 - Width OD: 30 - Profile: 26 - Weight: 390g - ERD: 587

Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set

- Aluminum hubs - Sealed bearing - Black - 6-bolt disc rotor

- Aluminum alloy shells resist corrosion and provide lightweight longevity - Sealed cartridge bearings offer smooth operation while resisting contaminants - 20mm Thru Axle with 15mm option, 6 bolt disc compatible

Replacement axle sets for use with Origin8 FB-2000 hubs Front Axle: - 3/8 x 26 x 135 x 175 Rear Axle: - 3/8 x 26 x 170 x 210

Converts CenterLock hubs to accept 6-bolt rotors - Available for standard Quick Release as well as Thru-Axle hubs - Extruded alloy collar with CNC shoulder pins and lock ring - Eliminates the need for rotor bolts

Proterra Light i23 wheels check all the boxes for a fast and light alloy wheelset. The 23mm inner rim width provides the optimal tire profile for adventure road and gravel tires ranging from 30-42mm. Its open-cavity profile features thin, weight-optimized walls that provide the perfect blend of stiffness, resilience, and efficiency. Subdued graphics on a bead-blast finish ensure these wheels won't clash with the colors of your dream bike. We didn't skimp on hubs either. Top-tier EZO bearings, a swift 6-pawl freehub, and 3.7 degrees of engagement provide the look, sound, and feel you expect of a high-end tubeless wheelset. - 23mm inner rim width with 28 spokes laced in a 3-cross pattern - 6069 aluminum alloy rim that is TCS 2.0 tubeless-ready - Sapim Secure Lock 14-gauge alloy nipples minimize rotational weight, while double butted 2.0/1.8/2.0mm J-bend spokes make replacement a breeze. - Tubeless tape, Solid Strip, and black alloy valves are preinstalled, making the wheels ready for tubeless tires the moment they arrive on your doorstep. The TCS 2.0 Solid Strip is a durable strip that lies beneath the tape, prevents it from sagging at the spoke holes, makes it easier to mount a tire, and protects from puncture in the case of a broken spoke. - Center Lock rotor mounts

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

- Holds one wheel securely for transport (up to 700c with 35mm CX tire installed). - Connects to second Zipp Connect wheel bag to transform into a double wheel bag. - Sturdy water-resistant EVA construction. - Includes removable axle/QR pocket.

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable

- Aluminum hubs - Sealed bearing - Nutted - Use: Rear - Gears: Flip-flop singlespeed freewheel - Drilling: 36H - Axle: 3/8-inch - Material: Alloy - Brake Type: Rim - OLD: 110mm - Bearing Type: Sealed

- Heat-treated axle for improved strength - Angled Flanges for lateral stability in wheel building - Rear hubs include a 4-Pawl Cassette body with 9-tooth driver - Use: Rear - Driver: Singlespeed cassette w/9T cog and lockring - Spacing / Axle: 14mm - Material: Alloy - Drilling: 48

- Nutted aluminum BMX hubs with cutout flanges for aesthetics and weight savings - Sealed bearing for improved performance and longevity - Use: Front - Drilling: 36H - Axle: 3/8-inch - Material: Alloy - Brake Type: Rim - OLD: 100mm

- Nutted aluminum BMX hubs with cutout flanges for aesthetics and weight savings - Sealed bearing for improved performance and longevity - Use: Rear - Gears: Flip/flop singlespeed freewheel - Drilling: 36H - Axle: 3/8-inch - Material: Alloy - Brake Type: Rim - OLD: 110mm

- Aluminum hubs - Sealed bearing - Nutted - Use: Rear 110mm - Driver: Singlespeed cassette w/12T cog and lockring - Axle: 3/8-inch - Material: Alloy - Brake Type: Rim - OLD: 110mm - Bearing Type: Sealed - Drilling: 36

- Front/Rear: Rear - OLD: 175mm

Replacement parts for Micro C-Drive Hubs. - Supplier Part: Replacement #16 Clutch Ring

Replacement axles for MX-2000 hubs. Size: 14 x 100 x 165mm - Supplier Part: KT-M18F - MPN: 370666 - Front/Rear: Front - Diameter: 14mm - OLD: 100mm Size: 14 x 110 x 180mm - Supplier Part: KT-389R - MPN: 370668 - Front/Rear: Rear - Diameter: 14mm - OLD: 110mm Size: 3/8-inch x 100 x 165mm - Supplier Part: KT-M17F - MPN: 370667 - Front/Rear: Front - Diameter: 3/8-inch - OLD: 100mm Size: 3/8-inch x 110 x 180mm - Supplier Part: KT-M88R - MPN: 370682 - Front/Rear: Rear - Diameter: 14mm slotted for 3/8-inch - OLD: 110mm

- Includes 9T Micro drive cog - Use: Rear - Driver: Singlespeed cassette w/9T cog and lockring - Drilling: 36H - Axle: Nutted 3/8-inch - Material: Alloy - Brake Type: Rim - OLD: 110mm - Bearing Type: Loose

- Replacement straight pull spokes for Zipp 88 (Front) and 188 (Rear) Hubs